MAM MB33 II (MK2) — Quick Reference & Technical Cheat Sheet

Monophonic analog bass synthesizer based on a VCO-VCF-VCA-ENV architecture with integrated sub-oscillator, 18 dB/oct lowpass filter, analog distortion, and full MIDI control.

1. Front Panel Controls & Architecture

Control Section Function & Technical Range
Waveform VCO Selects the primary oscillator waveform: Sawtooth or Square.
Mix VCO Blends between the Sub-Oscillator (Square wave, 50% duty cycle, 1 octave lower) and Main Waveform.
Fully Left: Sub-Osc only | Center: 50/50 Mix | Fully Right: Main Waveform only.
Tune VCO Fine tuning adjustment (±1 semitone). Center position matches standard MIDI pitch.
PWM VCO Controls the depth of Pulse Width Modulation on the Square wave via the main Envelope Generator.
Fully Left: Constant 50% duty cycle.
100% Depth: High envelope peaks momentarily cut off (mute) the Square wave and Sub-Osc, leaving only Sawtooth audible if mixed.
Cutoff VCF Sets the cutoff frequency of the 18 dB/oct lowpass filter (20 Hz – 20 kHz). Fully right leaves spectrum unfiltered.
Resonance VCF Boosts frequencies at the cutoff point up to self-oscillation. Maximum resonance depth can be trimmed via the rear panel ☢️
Env Mod VCF Sets the modulation intensity of the Envelope Generator onto the VCF cutoff frequency.
Accent Groove Sets the intensity of the Accent effect (triggered via MIDI Velocity ≥ 120). Affects volume, cutoff peak, and envelope decay time.
Decay ENV Sets the decay time of the main envelope generator (200 ms to 2.5 seconds). VCA uses an internal fixed envelope profile.
Distortion FX Controls the intensity of the analog overdrive circuit applied to the filtered signal. Interacts heavily with Cutoff and Resonance settings.

2. Accent, Autoslide & PWM Behavior

  • Accent Triggering: Triggered automatically on incoming MIDI notes with Velocity ≥ 120.
    • Boosts overall volume and raises filter Cutoff.
    • Decay Overwrite: During an accented step, main envelope Decay is forced to Minimum (~200 ms) for the duration of the accent.
    • Resonance Interaction: At low resonance, Accent produces a sharp, percussive cutoff punch. At high resonance, the cutoff boost is slightly delayed and smoother.
  • Autoslide (Legato Glide):
    • Autoslide ON: Overlapping MIDI notes (legato) trigger pitch slides automatically. The envelope generator does not retrigger on overlapping notes.
    • Autoslide OFF: Pitch sliding is disabled; every note re-triggers the envelope generator.

3. Rear Panel Connections & Trimming

VCF IN External audio input jack. Plugging a jack into VCF IN disconnects the internal VCO. The external signal passes through VCF & VCA and requires incoming MIDI Note-ON commands to trigger the VCA gate/envelope.
RES ADJUST Rear trimmer potentiometer to calibrate the maximum self-oscillation threshold when the front panel Resonance knob is at 100%.
DIP Switches (1–4) Binary selection for MIDI Receive/Send Channel (1 to 16).

4. MIDI Controller Implementation (CC Map)

For controllers 102 through 107, the CC values are inverted relative to standard conventions:
CC Value 0 = Maximum knob position (100%)  |  CC Value 127 = Minimum knob position (0%).
Parameter MIDI CC # CC Value Range Notes / Hardware Relation
Decay CC 102 0 (Max Decay) – 127 (Min Decay) Inverted values
Accent CC 103 0 (Max Accent) – 127 (Min Accent) Inverted values
ENV Mod CC 104 0 (Max Amount) – 127 (Min Amount) Inverted values
Distortion CC 105 0 (Max Drive) – 127 (Min Drive) Inverted values
Resonance CC 106 0 (Max Res) – 127 (Min Res) Inverted values
Cutoff CC 107 0 (Max Open) – 127 (Min Closed) Inverted values
Autoslide CC 108 0 = OFF  |  1 = ON Standard switch values

5. MIDI Edit Modes (NORM vs. MOVE)

  • NORM (Normal Mode): The synth responds directly to absolute incoming CC values or knob positions (whichever was moved last). Knob tweaks send real-time CC out over MIDI OUT.
  • MOVE Mode (Relative Offset Recording): Allows tweaking an existing CC sequence in real time. Incoming CCs are modified by adding/subtracting a physical knob offset:
    • Knob at 12:00 (Center): Incoming CC pass through unchanged (Offset = 0).
    • Knob rotated Right: Adds up to +64 to incoming CC values.
    • Knob rotated Left: Subtracts up to -64 from incoming CC values.
    • Modified CC data is streamed continuously out of MIDI OUT for DAW recording.

6. Hacks

1. VCF IN Feedback Loop Hack

Plugging a jack into the VCF IN socket automatically disconnects the internal VCO. By taking the main audio output and routing it back into VCF IN via an external mixer or Y-cable (while sending MIDI Note-ON events to gate the VCA and trigger the envelope), you create an analog feedback loop for saturated industrial acid textures.

2. Pushing the RES ADJUST Trimmer

The rear-panel RES ADJUST trimmer is not just for calibration. Turning it clockwise with a small precision screwdriver pushes the 18 dB lowpass filter far past its default self-oscillation threshold, causing intense filter screaming even at mid-range front-panel Resonance settings. (Note: Avoid turning it too far)

3. Pseudo Hard-Sync via Distortion & Peak Resonance

The analog distortion circuit is located post-filter. When Resonance is set high and Cutoff is opened, the sharp resonance peak overdrives the distortion stage, generating metallic harmonics that closely mimic oscillator hard-sync or ring modulation.

4. Rhythmic Sub-Bass Gating via PWM

At PWM = 100%, high envelope peaks temporarily cut off (mute) the Square wave and Sub-Oscillator entirely. When mixing Sawtooth and Sub-Osc (Mix knob at center), the sub-bass drops out on note attack and recovers as the decay trails off, creating an automatic sidechain-style pumping effect.

5. Maximizing Accent Dynamic Range

When an Accent is triggered (MIDI Velocity ≥ 120), the internal circuit forces the envelope Decay to its minimum (~200 ms) regardless of the front panel Decay setting[cite: 6]. To maximize contrast, crank the front panel Decay knob high (1:00 to 3:00 o'clock). Unaccented notes will sustain smoothly, while accented steps cut through with a short, punchy decay.